As cliché because it sounds, it feels prefer it was solely yesterday the final time I up to date everybody on Venture Tough’s journey. That feeling of ‘solely yesterday’ interprets into over two years of actuality.
It’s mind-boggling to me that 24 months have already handed. Nonetheless, the truth that my youngest is approaching three and continually tries to have full-blown conversations with me confirms it. So, what about Tough, the ER34 Nissan Skyline GT-T? Is the venture nonetheless a venture? Do I nonetheless even have it?
The latter query doesn’t have to be addressed as a result of I’ve titled this publish The Mega Replace, however let’s dive into the opposite questions on Venture Tough – notably, what has modified within the final two years.
Extra Alignment Goodies
Since my final expertise performing DIY alignments, I’ve continually redesigned my rig and strategy to enhance the outcomes.
I’ve designed a transportable ramp and platform system that permits me to lift the automobile a bit greater off the bottom to work on it with out lifting it and inflicting binding. I lastly invested in a set of turntables, as any DIY-style system lacked accuracy and repeatability. I additionally purchased a laser stage to make sure that the platform was stage on all 4 corners, growing its accuracy.
The modifications have labored and made performing alignments a breeze. One ultimate factor I wanted to do was change my caster arms. In some unspecified time in the future throughout all of the suspension modifications that I made over time, the large clearance design of the arms interfered with the entrance sway bar, blocking its movement of journey.
After all, it wouldn’t be a Venture Tough replace if one thing didn’t struggle me whereas making an attempt to take away it…
GKTech got here to my rescue as soon as once more with its tubular caster arms, and swapping them in was moderately easy. With the sway bar accessing its full size of journey and one other session on my alignment rig, the dealing with grew to become much more elegant.
It’s humorous how eliminating binding in your suspension could make an enormous distinction.
The Goofy Clutch Pedal
Shopping for a automobile with a transmission swap is certain to be a bit goofy. The whole lot is unknown; numerous corners may have been sliced off to make an set up work. The automobile got here with an OS Giken single-plate metallic clutch, and I had already changed the slave grasp, rebuilt the clutch grasp cylinder, and put in a Premium CUBE Velocity brief shifter.
Nonetheless, the clutch pedal all the time appeared odd to me. It was abnormally near the brake pedal and, for no matter purpose, had pink rattle can spray paint on the highest half.
Upon nearer inspection, I seen the pedal had been hammered on the bend. Maybe whoever put in the transmission swap had tiny ft and wished the pedals nearer for consolation.
I don’t have tiny ft, and if I may bend the pedal again to its unique place and even additional towards the foot relaxation, I may drastically enhance the ergonomics and cease tweaking my left foot into a clumsy place to depress the clutch. Re-bend full – I’ll tackle the funky look later, I promise!
Exterior… Lastly
I’ve talked about earlier than in my SH Storage updates that my Skyline is as a lot an training piece as it’s a accomplice. If there’s something that I’m inquisitive about or strategies I’d like to check out in the true world, Tough is my sandbox.
My objective is to develop a brand new ability set so I can create a useful aero package from carbon fiber. Having spent numerous hours researching and with Tough driving like a deal with, now was lastly time to start out addressing the tough exterior.
The OEM entrance lip that got here with the automobile has been certainly one of my largest eye sores. In my infinite knowledge, I assumed creating a carbon fiber lip can be straightforward, by no means thoughts that I’ve by no means constructed something of this dimension earlier than and even made a correct mould. So why not create a lip made with a finicky and unforgiving materials?!
Diving Into The Unknown
For this venture, I made a decision to forgo the care of operate and simply deal with making it look first rate. I used the unique lip as my base for the half, wrapping it with aluminum foil and tape to type a barrier from the resin.
I wished to change the design to make it extra of my very own and enhance the fitment on the bumper. I crammed within the hole on the passenger facet, which was designed to clear the oil cooler vent on the OEM bumper, and prolonged the flanks to relaxation greater on the bumper to extend the visible affect.
The place the OEM lip is delicate, I wished this to be the centerpiece in your eyes when Tough front-on.
With my fiberglass lip trimmed and becoming the way in which I used to be blissful, I coated your entire lip in bondo (physique filler) to offer me a layer I may sand flat. I had purchased what I assumed was a ‘common’ sort filler from the native dwelling heart.
For no matter purpose, the bondo didn’t cowl the floor space I had anticipated it to, and it was a ache to construct up layers.
Deep down, I knew one thing wasn’t proper once I used a complete kilogram of fabric to cowl the lip, however I pressed on to primer regardless.
I used an automotive rattle can to use the primer coat. Don’t do that. I didn’t understand it on the time, but it surely was going to chunk me within the ass when it got here to mould cleanup.
The primer revealed that I had executed a horrible job overlaying and flattening the lip, though I had spent an embarrassing period of time sanding. Determined to determine what I may have executed fallacious, I sought steering from Akira-san, the creator behind Studio Allica and Omomuki’s carbon fiber 911. He identified that the bondo I used to be utilizing to cowl the lip was a ending model designed to take away pinholes and different imperfections, and he recommended that I purchase a rough physique filler to cowl the lip.
Armed with this invaluable perception, I bought the proper bondo, made a DIY information coat with floor charcoal sticks, and started working getting the lip surfaces as flat as attainable earlier than including a few primer coats.
It was time to create a mould with the lip sanded to 2,000 grit and polished to a excessive gloss. I briefly made flanges out of cardboard cutouts to behave as templates.
With the general sample to my liking, I transferred the template to a big polypropylene sheet.
I deliberate on including a wholesome dose of mould launch to the flanges, however resins like polyester and epoxy received’t persist with polypropylene sheets, making them glorious for flanges or as boundaries for break up molds. In some locations, the gaps between the half and flanges have been massive, so I used silicone to easy out the transitions.
By no means Give Up
At this level, I noticed that though a lip appeared like a small half at first, its floor space is much from small. This meant I used to be about to make use of a wholesome dose of gel coat and resin to make this mould. There are alternative ways to make the mould, and my technique may use enhancements.
As soon as the gel coat was cheesy, I added one layer of fiberglass sheets, then two layers of chopped fiberglass, and strategically positioned sheets of woven roving fiberglass for extra power on the bends and largely flat areas. I topped it off with one other layer of chopped fiberglass. If I have been to do it once more, I’d place the woven roving final, because it made chasing air bubbles on the ultimate layer a nightmare.
With the mould absolutely cured, I spent a bit below an hour demolding.
Bear in mind, this was the primary time making one thing massive and sophisticated, so the very last thing my coronary heart may take was damaging the mould or discovering I had screwed up catastrophically. Sluggish and regular was the secret.
Facet word: Picket chopsticks make for glorious wedges.
The plug got here out revealing a reasonably rattling good mould with just a few blemishes. Whew!
Keep in mind that rattle can primer? The warmth generated from curing brought on a few of the paint to switch onto the mould, so I needed to spend a further hour scraping it off earlier than I may put together the mould for carbon.
I designed the mould to carry out a vacuum bagging infusion, however I made a decision to start out easy with a moist layup. This meant that laying in a big sheet of carbon can be a nightmare.
I may lower the carbon fiber into smaller sections and lay them in order that the ends can be hidden. I used fiberglass sheets to assist make templates for reducing the carbon to attenuate waste.
At this level, I ought to have identified that I wanted to stabilize the ends to stop them from fraying, however I despatched it anyway.
Plan Chopped
As soon as the carbon fiber had cured, I pulled my first half from the mould with out drama. Then, I noticed I had an issue – it regarded like sh*t.
Sure, moist layups would require extra ending work to look proper, and I knew this was its ugly duckling part.
Nonetheless, that didn’t cease my coronary heart from sinking. In any case that work and preparation, it regarded like this. Typically, you should take a break and let your mind and feelings reset barely to suppose clearly. After I did that, I got here up with a brand new plan.
Now that the half was out of the mould, I may simply add one other sheet of carbon, creating a brand new beauty pores and skin layer…
…or, I may proceed sending it and create a cast carbon look as the brand new cosmetics layer. Since I’ve been sending it like this to date, why cease now?
The issue with this plan was that I usually dislike the looks of cast carbon. This led me down the rabbit gap of small-scale testing several types of carbon fiber materials and tows, lower to varied lengths, to create a sample I appreciated.
I then spent a lot time sanding and filling low spots with a syringe and wax dams. This technique of sanding and filling went on greater than it wanted to, however you are usually additional cautious while you’re experimenting and have a ton of time and sources invested into the method.
The completed outcomes are removed from good, however I’m proud that I used to be capable of get it so far.
I tousled the fitment that I labored so onerous to have on the plug, and I sanded a bit an excessive amount of of the cast carbon beauty layer off, chasing my tail getting all the things flat. I additionally ought to redo the UV high coat to take away the runs from making an attempt to construct up layers too quick. The carbon fiber lip is just resting on the bumper in these photos.
It could be straightforward for me to stay dissatisfied as a result of the lip remains to be not good. Nonetheless, the extra I have a look at it, the happier I turn out to be. I took on the problem of creating a big, complicated half from scratch utilizing tough supplies.
Much more importantly, I gained a wealth of information and confidence that I can apply instantly to enhance this and the following half.
It reveals that the end result isn’t all the time essentially the most vital issue. We shouldn’t turn out to be so tunnel-visioned about attaining a selected goal or objective that it blocks out different potentialities to realize the identical factor or one thing much more exceptional.
I can’t wait to use what I discovered on this venture to the following piece of the puzzle for Venture Tough. I’ll ensure that it occurs sooner fairly than two years later.
Ron Celestine
Instagram: celestinephotography
